Dirt Modified and IMCA Racing Oil Filter Guide: Open Engine Class Filter Selection

May 6, 2026 By Costa Oil Filters Team

IMCA racing is the backbone of short-track dirt racing in the United States — more than 70 sanctioned tracks nationwide, more total entries than any other dirt sanctioning body, and a class structure that covers everything from bone-stock factory engines to open-engine Modified builds running 400+ horsepower. The oil filter requirements vary significantly across IMCA classes based on thread spec, engine type, and class rules. This guide covers every major IMCA and open dirt modified application, with specific filter recommendations and change intervals for each format.

Engines: SB Chevy Open Dirt Modified, GM Factory Stock, IMCA Hobby Stock, Street Stock Engine, DIRTcar Modified  |  Classes: IMCA Modified, IMCA Stock Car, IMCA Hobby Stock, IMCA Street Stock, DIRTcar Modified, UMP Modified

Spec Comparison: Costa COF241 vs WIX 51036R vs FRAM PH8

Spec Costa COF241 WIX 51036R FRAM PH8
Thread Size 3/4-16 UNF 3/4-16 UNF 3/4-16 UNF
Filter Height 3.10″ 3.20″ 3.44″
Filtration Media High-flow synthetic fiber Semi-synthetic blend Cellulose / fiberglass mix
Filtration Efficiency 20µ @ 98% 25µ @ 95% 35µ @ 90%
Bypass Valve Pressure 13 psi 11 psi 8–10 psi
Burst Pressure Rating > 500 psi 350 psi 200 psi
Anti-Drain-Back Valve Yes Yes Yes

IMCA Modified: Open Engine, Race-Grade Filter Required

The IMCA Modified class runs open small block engines — primarily SB Chevrolet builds in the 350–358ci range — in the $10,000–25,000 range depending on builder and program level. These engines run on dirt, generate significant airborne abrasive contamination from dirt ingestion past the air filter, and run hard features in 25–40 lap formats at weekly tracks.

For IMCA Modified applications with 3/4-16 UNF filter threads: COF241 (COF-21100, 3/4-16 UNF, 3.10″ height). This is the compact 3/4-16 UNF race filter designed for tight clearance Modified chassis filter locations. It replaces WIX 51036R and FRAM PH8 with 20-micron synthetic media and a 13 psi bypass valve.

For 13/16-16 UNF thread Modified applications (less common): COF111 (COF-21100, 13/16-16 UNF). Same synthetic media and race spec as COF241, different thread. Verify your block before ordering.

IMCA Stock Car and Street Stock: Factory Engine Filter Strategy

IMCA Stock Car and Street Stock classes run factory-based production engines with limited modification. These classes often specify OEM-equivalent replacement parts or approved aftermarket equivalents. The specific filter thread depends on the engine type — GM production engines in these classes typically run 13/16-16 UNF threads, which takes COF40 (for GM 602/604 equivalent applications) or COF111.

For production-based IMCA Stock Car and Street Stock programs, the economics of racing weekly on a tight budget push teams toward the cheapest available filter. The counter-argument: at an engine value of $2,000–5,000 for a competitive stock car motor, a $12 cost savings on a filter is not worth the risk of running a street-grade bypass valve through a full season. At weekly racing pace — 25–30 nights per season — the filter change interval for these classes is every event.

IMCA Hobby Stock: The Budget Racing Class Filter Decision

IMCA Hobby Stock runs factory stock engines in vehicles valued at $1,000–3,000. These programs often involve teams that are learning to race, teenagers in their first car, or adults running the most affordable racing format available. The filter question in Hobby Stock is primarily economic.

The correct filter for a Hobby Stock running a stock GM engine is the one with the highest bypass pressure and best media that fits the budget. COF40 or COF111 at $16–18 represents 1–2% of the total car value and provides significantly better protection than a $6 FRAM street filter. For teams running weekly on a true shoestring, at minimum avoid FRAM street-grade filters — they are not appropriate for race applications. WIX 51061R (for 13/16-16 UNF) is an acceptable middle ground if the budget genuinely cannot support a Costa filter.

Dirt Environment: Why Filtration Efficiency Matters More on Dirt

Dirt oval racing creates an airborne contamination environment that asphalt racing does not. Ground-up clay and limestone track material is in the air constantly — on a dusty night, it penetrates past even well-maintained air filters and finds its way into the engine oil via blowby past piston rings. The particles involved are in the 10–40 micron range — small enough to be partially filtered by the oil, but significant enough to accelerate wear on precisely ground bearing surfaces.

A filter that operates at 35 microns (FRAM PH5/PH8) passes dirt-derived particles that a 20-micron filter (COF series) would capture. Over a 30-race season on a dirt track, that difference in filtration efficiency accumulates in your bearings and on your cam lobes. The dirt racing environment is an argument for better filtration, not a reason to use whatever’s available.

Post-Rain Events: Extra Filter Vigilance

Dirt tracks run after rain are significantly dustier as the surface dries during the event — and more abrasive. Track prep clay and conditioner applied to a wet surface, then driven through for three classes before your feature, creates conditions where air filter maintenance and oil filtration are under elevated stress.

For any race night that started wet, inspect your air filter element between classes and change your oil filter after the event regardless of where you are in your normal interval schedule. A single event on a dirty, drying track can deposit more contamination in your engine oil than three events on a well-prepped sealed surface. This is particularly important for open-engine Modified programs where engine replacement costs are significant.

IMCA National Events: When to Change Mid-Weekend

IMCA national events — the IMCA Speedway Motors Super Nationals at Boone Speedway, the Fall Jamboree, and regional tour events — run multi-day formats with heat races Thursday and Friday, B-mains Friday, and A-main Saturday. For serious national programs (top 25 in IMCA Modified national points), the filter change protocol should be:

Thursday night after hot laps and heats: change oil and filter. The first night of a national event is the highest-wear event because engines are at peak sharpness and racing in heats for position. The filter captures everything from that high-intensity session.

Saturday before the feature: inspect the Thursday-changed filter (cut and examine), change oil and filter again with a fresh COF241 or COF111. Go into the Saturday A-main with clean oil and a fresh filter. This is the standard for programs that take national events seriously.

Verdict

COF241 (3/4-16 UNF, 3.10″ compact body) for IMCA Modified and open dirt modified applications with tight chassis filter clearance. COF111 (13/16-16 UNF) for production-block IMCA Stock Car and Street Stock applications. Change every event — the dirt racing environment is harder on oil filtration than almost any asphalt format. Cut and inspect your filter after every change. For multi-day national events, change oil and filter twice: after the first race night and before the Saturday A-main.

Buy the Costa COF241 →